Homepage

Product of
the Month

Product Applications

Product
Catalog

Studies/
Reports

Crosswalk Crusaders

Media Room

Engineering/
Installation Support

How to Specify Our Products

Installation
Gallery

Contact Us

Links

General Description
The TS520 stainless steel fixture is designed to be used in conditions where a wide beam of light (60 degree wide beam) is required to flood a large area. The TS520's outstanding durability, superior brightness and low maintenance design make them ideal to be used in the most demanding environmental conditions, and in solar powered applications because of its energy efficient design. The TS520 comes standard as a bi-directional fixture, but may be configured to a uni-directional fixture (TS521).

The TS520 is typically used in applications requiring flood lighting of wide areas such as parking lots, park areas, beach areas and in applications where a "dark sky, turtle friendly" type of lighting is required.

Why Our TS520 Is Better

Outstanding Durability
• Corrosion resistant stainless steel construction provides resistance to salt, chemicals, traffic wear and weathering.
• High static load rating (44,000 lb.) reduces likelihood of damage from heavy vehicles.

Superior Brightness and Energy Efficiency
• Highbright LEDs produce a brightness level of over 600,000 candela per meter squared making them clearly visible in daytime and under the worst weather conditions.
• Highbright 12 Volt LEDs consume only 9.0 watts/fixture making them ideal for energy efficient solar power applications.

Low Maintenance
• Re-usable design reduces the cost, effort and time during resurfacing of the road.
• Self-cleaning lens design reduces build-up of dirt and need for frequent cleaning.
• Pressurized light cavity keeps moisture out and reduces the frequency of replacement.
• Pre-focused optics eliminates the requirement of field adjustments.
• Long life LEDs (Average rated life of 10 years) reduces the frequency of replacement.

How to Specify the TS520 Wide-Beam, Self-Cleaning, Bi-Directional Fixture
Download Specs (Word format)

The fixture shall be model FI-TS520 as marked by Traffic Safety Corporation or approved equal. In order to be considered equal, the alternate fixture shall satisfy the following requirements:

Construction - Fixture shall be bi-directional and of modular design comprised of 6 major parts with the top casting of stainless steel and the bottom casting of high tensile strength aluminum alloy. The top and bottom castings shall be sealed by means of a flat gasket. Fixture shall have a smooth shaped face projecting not more than 0.50" when installed in the factory provided mounting base. The fixture shall incorporate a self-cleaning design with an outward sloping light channel to promote drainage and facilitate maintenance. Diameter shall not exceed 8" and all mounting hardware shall be stainless steel. Fixture will operate on 12 VDC and be furnished pre-wired with a waterproof 90P plug.

Durability - Fixture shall withstand a static load of 44,000 lb. without sustaining permanent deformation or cracking of materials. Leads, gaskets, etc. shall be rated to withstand 300 degrees F.

LED/Light Cavity - The lenses shall be molded high performance optical grade glass and formed to provide a sealed fit within the fixture and shall be gasketed by high density silicone rubber. There will be two lenses per fixture, one aimed at 0 degrees and the other aimed at 180 degrees. The fixture's optics shall be pre-focused to simplify maintenance. To prevent moisture intrusion, each fixture shall be installed with a Schraeder valve to facilitate verification that the entire assembly is sealed at the time of installation and to allow for re-testing after maintenance.

Photometric Performance - The fixture shall produce a brightness level of more than 600,000 candela per meter squared using a yellow 12 Volt, 9 watt LED array. The dominant wavelength of the yellow LED array shall be 600nm.

Finish - The top cover shall be matte finish stainless steel while the bottom cover shall be black powder coat.

Mounting Base - Fixture shall be installed in mounting base (TSC's # BA-700-10) of high strength steel, hot dip galvanized after fabrication per ASTM-153 specifications, with a 7" diameter bolt circle, a 1" mud ring, and standard base depth of 10". The base shall be supplied with a plywood cover to protect the mounting flange during installation.

Warranty - The TS520 shall be warranted against defects in workmanship and materials for one year from date of shipment and is eligible for TSC's 5-Year Limited System Warranty.